Televisions
Crown XLS602 Power AmpCrown |
|
 |
The XLS Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. CLICK HERE TO BUY XLS 602: 380W per channel @ 4 Ohm 600W per channel @ 8 Ohm 1200W bridge mono @ 8 Ohm The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. The four models in the series are the XLS-202, XLS-402, XLS-602, and XLS-802. They are identical except for output power and weight. XLS Series amplifiers are professional stereo power amplifiers engineered to meet demanding audio requirementsreliably and within budget. Plus, every XLS Series amplifier is backed by Crowns unequaled Three-Year, No-Fault, Fully-Transferable Warranty that covers everything. With over five decades of experience designing and building rock-solid products, Crown is the standard in amp technology. So check out the affordable, Crown XLS Series. They are a powerful argument for quality and value! Features Reliable design incorporates many popular features Housed in a rugged, all-steel 2U chassis Efficient forced-air fans prevent excessive thermal buildup Electronically balanced XLR inputs; touchproof binding post and Speakon® outputs Precision detented level controls, power switch, power LED, and six LEDs which indicate signal, clip and fault for each channel. Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications Performance Sensitivity (volts RMS) for full rated power at 4 ohms: 1.25 V. Frequency Response (at 1 watt) 22 Hz to 20 kHz: +0 dB, –0.8 dB. Signal-to-Noise Ratio (20 Hz to 20 kHz) A-weighted, below rated power: >98 dB. No weighting, below rated power: >93 dB. Total Harmonic Distortion (THD): 200. Crosstalk (below rated power) at 1 kHz: –76 dB. at 20 kHz: –58 dB. Input Impedance (nominal): 20 kilohms balanced, 10 kilohms unbalanced. Load Impedance: Rated for 2 to 8 ohms per channel in Stereo, 4 to 8 ohms in Bridge Mono. AC Line Voltage and Frequency Configurations Available (±10%): 120 VAC 60 Hz, 100 VAC 50/60 Hz, 220 VAC 50 Hz, and 230-240 VAC Controls Level: Two front-panel rotary level controls, one for each channel. Power: Front-panel switch; on when in the IN position. Circuit Breaker: Back-panel breaker provides overload protection. Mode Switch: Back-panel switch selects Dual or Bridge-Mono mode. Indicators Signal Presence Indicators: Two green LEDs, one for each channel, illuminate when the channel’s input signal exceeds –40 dBu. Clip Indicators: Two red LEDs, one for each channel, illuminate when the channel’s output is being overdriven. Power Indicator: Blue LED indicates amplifier has been turned on and AC power is available. Fault Indicator: Two red LEDs illuminate when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on. Input/Output Input Connectors: One per channel; back-panel three-pin female XLR input connectors. Output Connectors: Two 4-Pole Speakon® Output Connectors accept 2-pole or 4-pole Speakon connectors. The top Speakon connector is wired for both channels so it can be used for bridge-mono wiring or for stereo wiring of two speakers to a single Speakon connector. One pair of back-panel binding posts per channel; accepts banana plugs or bare wire. (European models do not accept banana plugs.) XLS-602: 29.0 lb (13.2 kg) Click here for more info |
Crown XS1200 Power AmpCrown |
|
 |
The Xs Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. CLICK HERE TO BUY XS1200: 1600W per channel @ 2 Ohm 1100W per channel @ 4 Ohm 650W per channel @ 8 Ohm 3000W bridge mono @ 4 Ohm 2300W bridge mono @ 8 Ohm Features Housed in a rugged, all-steel 2U chassis. Efficient forced-air fan prevents excessive thermal buildup. XLR-1/4" combo inputs, 3-pin Phoenix-style inputs, daisy-chain XLR outputs, touch-proof binding post outputs and Speakon outputs. Precision detented level controls, power switch, and five LEDs which indicate clip for each channel, power, AC mains, temperature and fault conditions. Microprocessor-controlled protection system. Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications. Performance Power Output: See power charts above. Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18 Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB. Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%. Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200. Crosstalk (below rated power): Xs1200 (1 kHz, 20 kHz): >65 dB, >45 dB Voltage Gain (at maximum level setting): Xs1200: 47.4:1 (33.5 dB) Controls Level: Two or four front-panel, gray rotary level controls, one for each channel. Power: Front-panel switch; on when in the right-hand position. Indicators Signal: Two or four green LEDs, one for each channel, illuminates when the channels input signal level is above 40 dBu. Clip: Two or four front-panel red LEDs, one for each channel, illuminates when the channels output signal is being overdriven. Power: Yellow front-panel LED indicates amplifier has been turned on and AC power is available. AC Mains: Red front-panel LED indicates the presence of AC power at the power cord, even if the amplifier is not turned on. Fault: Red front-panel LED illuminates when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on. Bridge: Yellow LED indicates that amplifier is in bridge mode (Channels 1 and 2, Channels 3 and 4 in Xs 4300). Temp: Red LED indicates that channel(s) are in thermal protect mode. Input/Output Input Connectors: XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals. Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms. Output Connectors: Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. Note: Binding post outputs on European models come with safety plugs installed to prevent European power-cord plugs from being inserted. The top & bottom entry positions for these connectors should therefore be used with European models. 4-Pole Speakon output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector. Click here for more info |
Crown XS700 Power AmpOther |
|
 |
The Xs Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. CLICK HERE TO BUY XS700: 900W per channel @ 2 Ohm 750W per channel @ 4 Ohm 450W per channel @ 8 Ohm 1900W bridge mono @ 4 Ohm 1645W bridge mono @ 8 Ohm Features Housed in a rugged, all-steel 2U chassis. Efficient forced-air fan prevents excessive thermal buildup. XLR-1/4" combo inputs, 3-pin Phoenix-style inputs, daisy-chain XLR outputs, touch-proof binding post outputs and Speakon outputs. Precision detented level controls, power switch, and five LEDs which indicate clip for each channel, power, AC mains, temperature and fault conditions. Microprocessor-controlled protection system. Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications Performance Power Output: See power charts above. Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18 Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB. Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%. Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200. Crosstalk (below rated power): Xs500 (1 kHz, 20 kHz): > 55 dB, > 55 dB Xs700 (1 kHz, 20 kHz): > 55 dB, > 55 dB Xs900 (1 kHz, 20 kHz): > 67 dB, > 62 dB Xs1200 (1 kHz, 20 kHz): >65 dB, >45 dB Xs4300 (1 kHz, 20 kHz): > 57 dB, > 40 dB Voltage Gain (at maximum level setting): Xs500: 32:1 (30.1 dB) Xs700: 38:1 (31.6 dB) Xs900: 42:1 (32.5 dB) Xs1200: 47.4:1 (33.5 dB) Xs4300: 25:1 (27.8 dB) Load Impedance: Safe with all types of loads. Xs500, 700, 900, 1200: 2 to 8 ohms in Stereo, 4 to 8 ohms in Bridge Mono. Xs4300: 4 to 8 ohms in Stereo, 8 ohms in Bridge Mono. Controls Level: Two or four front-panel, gray rotary level controls, one for each channel. Power: Front-panel switch; on when in the right-hand position. Indicators Signal: Two or four green LEDs, one for each channel, illuminates when the channels input signal level is above 40 dBu. Clip: Two or four front-panel red LEDs, one for each channel, illuminates when the channels output signal is being overdriven. Power: Yellow front-panel LED indicates amplifier has been turned on and AC power is available. AC Mains: Red front-panel LED indicates the presence of AC power at the power cord, even if the amplifier is not turned on. Fault: Red front-panel LED illuminates when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on. Bridge: Yellow LED indicates that amplifier is in bridge mode (Channels 1 and 2, Channels 3 and 4 in Xs 4300). Temp: Red LED indicates that channel(s) are in thermal protect mode. Input/Output Input Connectors: XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals. Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms. Output Connectors: Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. Note: Binding post outputs on European models come with safety plugs installed to prevent European power-cord plugs from being inserted. The top & bottom entry positions for these connectors should therefore be used with European models. 4-Pole Speakon output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector. Click here for more info |
Crown XS900 Power AmpCrown |
|
 |
The Xs Series of power amplifiers from Crown represents a new era in affordable, quality power amplification. The line consists of four models in a uniform, rugged 2U chassis, incorporating the best of tried-and-true design principles and innovative features. CLICK HERE TO BUY Features Housed in a rugged, all-steel 2U chassis. Efficient forced-air fan prevents excessive thermal buildup. XLR-1/4" combo inputs, 3-pin Phoenix-style inputs, daisy-chain XLR outputs, touch-proof binding post outputs and Speakon outputs. Precision detented level controls, power switch, and five LEDs which indicate clip for each channel, power, AC mains, temperature and fault conditions. Microprocessor-controlled protection system. Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment and guarantees its specifications. Performance Power Output: 600W per channel @ 8 Ohms 900W per channel @ 4 Ohms 1200W per channel @ 2 Ohms Sensitivity (volts RMS) for full rated power at 4 ohms: 1.4V Frequency Response (at 1 watt): 22 Hz to 22 kHz: 1 dB. Phase Response (degrees at 1 watt, 20 Hz to 20 kHz): +5, 18 Signal-to-Noise Ratio: A-weighted, below rated power: > 102 dB. 22Hz to 22kHz, below rated power: > 97 dB. Total Harmonic Distortion (THD) at full bandwidth power, from 20 Hz to 20 kHz: 0.5%. Intermodulation Distortion (IMD): (60 Hz and 7 kHz at 4:1) from full rated output to 40 dB: < 1%. Damping Factor (8 ohm) 10 Hz to 400 Hz: > 200. Crosstalk (below rated power): Xs900 (1 kHz, 20 kHz): > 67 dB, > 62 dB Voltage Gain (at maximum level setting): Xs900: 42:1 (32.5 dB) Load Impedance: Safe with all types of loads. Xs500, 700, 900, 1200: 2 to 8 ohms in Stereo, 4 to 8 ohms in Bridge Mono. Controls Level: Two or four front-panel, gray rotary level controls, one for each channel. Power: Front-panel switch; on when in the right-hand position. Indicators Signal: Two or four green LEDs, one for each channel, illuminates when the channels input signal level is above 40 dBu. Clip: Two or four front-panel red LEDs, one for each channel, illuminates when the channels output signal is being overdriven. Power: Yellow front-panel LED indicates amplifier has been turned on and AC power is available. AC Mains: Red front-panel LED indicates the presence of AC power at the power cord, even if the amplifier is not turned on. Fault: Red front-panel LED illuminates when amplifier is in protect mode. Also illuminates briefly during normal power-up when amplifier is first switched on. Bridge: Yellow LED indicates that amplifier is in bridge mode (Channels 1 and 2, Channels 3 and 4 in Xs 4300). Temp: Red LED indicates that channel(s) are in thermal protect mode. Input/Output Input Connectors: XLR-1/4" combo connectors: One per channel, 3-pin female XLR connector and TRS 1/4" phone jack accept balanced or unbalanced signals. 3-pin Phoenix-style connectors (2-channel models only): One per channel, accepts balanced or unbalanced signals. Input Impedance (nominal) balanced, unbalanced: 20 k ohms, 10 k ohms. Output Connectors: Balanced XLR connectors (2-channel models only): One per channel, 3-pin male XLR connector in parallel with XLR-1/4" combo and Phoenix-style input connectors for daisy-chain operation. 5-Way binding post output connectors: One pair per channel; accept banana plugs, spade lugs or bare wire. Note: Binding post outputs on European models come with safety plugs installed to prevent European power-cord plugs from being inserted. The top & bottom entry positions for these connectors should therefore be used with European models. 4-Pole Speakon output connector (2-channel models only): One connector per channel. Accepts a 4-pole Speakon connector. Click here for more info |
returned - Page 1 of 0